A raised logo turns a cap into a premium product. In 3D embroidery, also called puff embroidery, a thin foam is covered with dense satin stitches. The needle perforates the foam along the edges, the rest is removed, and the design stands up from the fabric where you can see and feel it.
Which designs work in 3D?
Bold, simple shapes, large lettering and satin stitches 3 to 10 mm wide on firm fabrics, above all on caps. Not suitable: lines under 3 mm, small fine lettering, satin stitches wider than about 10 mm, fill stitches and stretchy fabrics.
What you need
• Puffy foam, 2 to 6 mm, 3 mm is the standard, in a colour that matches the thread
• Polyester thread, weight 40, strong and heat resistant
• Needle DBxK5, size 75 to 90, sharp point
• Cap backing behind the front panel
• Heat gun and tweezers for finishing
You will find matching foam in the ZSK Parts Shop: Würker 3D Puffy Foam.
Rules for the embroidery file
• Satin stitch only, at roughly double density so no foam shows through
• Stitch width at least 3 mm, at most about 10 mm
• Close the ends: cap the edges at a 90° or 45° angle
• Stitch in one pass from bottom to top, without overlaps
• Flat parts first, 3D parts afterwards
Machine settings
As a guide: about 700 stitches per minute, raise the presser foot by the foam thickness and check that the upper thread lies cleanly on the foam. Always stitch a sample first.
Six steps to a 3D cap
1. Plan the design: areas instead of lines, decide what becomes 3D
2. Hoop the cap tightly with backing
3. Stitch the flat parts, the machine stops for the foam
4. Place foam slightly larger than the design
5. Stitch and watch the first satin stitches
6. Pull the foam off in one piece, remove leftovers, apply heat briefly
Common mistakes
Foam shows through. Density too low or an open end. Increase density and close the ends.
Frayed edges. Foam too soft or needle blunt. Use firmer foam and a new, sharp needle.
Thread breaks. Usually too fast or tension too high. Slow down to about 700 stitches per minute.
Design looks flat. Satin stitch too wide or foam too thin.
More in our customer magazine CARL
Why 3D embroidery on caps is boosting sales right now is the subject of the article "Cap is the new premium" in CARL Spring 2026, page 22. Would you rather not create the 3D file yourself? For several years we have developed the designs for our trade show appearances together with Vitor Digitizing, including complex 3D caps. The portrait is in CARL on page 23, contact via vitordigitizing.net.
Free video course
We show every step in five short videos in the free course 3D Puff on Caps (about 8 minutes).
Which designs work in 3D?
Bold, simple shapes, large lettering and satin stitches 3 to 10 mm wide on firm fabrics, above all on caps. Not suitable: lines under 3 mm, small fine lettering, satin stitches wider than about 10 mm, fill stitches and stretchy fabrics.
What you need
• Puffy foam, 2 to 6 mm, 3 mm is the standard, in a colour that matches the thread
• Polyester thread, weight 40, strong and heat resistant
• Needle DBxK5, size 75 to 90, sharp point
• Cap backing behind the front panel
• Heat gun and tweezers for finishing
You will find matching foam in the ZSK Parts Shop: Würker 3D Puffy Foam.
Rules for the embroidery file
• Satin stitch only, at roughly double density so no foam shows through
• Stitch width at least 3 mm, at most about 10 mm
• Close the ends: cap the edges at a 90° or 45° angle
• Stitch in one pass from bottom to top, without overlaps
• Flat parts first, 3D parts afterwards
Machine settings
As a guide: about 700 stitches per minute, raise the presser foot by the foam thickness and check that the upper thread lies cleanly on the foam. Always stitch a sample first.
Six steps to a 3D cap
1. Plan the design: areas instead of lines, decide what becomes 3D
2. Hoop the cap tightly with backing
3. Stitch the flat parts, the machine stops for the foam
4. Place foam slightly larger than the design
5. Stitch and watch the first satin stitches
6. Pull the foam off in one piece, remove leftovers, apply heat briefly
Common mistakes
Foam shows through. Density too low or an open end. Increase density and close the ends.
Frayed edges. Foam too soft or needle blunt. Use firmer foam and a new, sharp needle.
Thread breaks. Usually too fast or tension too high. Slow down to about 700 stitches per minute.
Design looks flat. Satin stitch too wide or foam too thin.
More in our customer magazine CARL
Why 3D embroidery on caps is boosting sales right now is the subject of the article "Cap is the new premium" in CARL Spring 2026, page 22. Would you rather not create the 3D file yourself? For several years we have developed the designs for our trade show appearances together with Vitor Digitizing, including complex 3D caps. The portrait is in CARL on page 23, contact via vitordigitizing.net.
Free video course
We show every step in five short videos in the free course 3D Puff on Caps (about 8 minutes).
