3D Puff on Caps: Logos That Pop
Raised logos turn a cap into a premium product. Five short videos show you 3D puff embroidery step by step: which designs work, which foam, needle and backing to use, how to digitize for 3D and how to set up your machine. Free, 8 minutes, with a checklist for every job.
-
5 lessons
Short videos -
8 minutes
Total video time -
All levels
Basics are enough -
100% free
Just sign up

Your trainer
Lorenz Wagner
Regional Sales Manager · Walz Solutions
Made for embroiderers who want more
3D puff embroidery looks difficult and is surprisingly simple once you know the rules. Every lesson explains one step in plain language and ends with a tip you can use at your machine today. The foam and cap backing shown in the videos are available at parts.zsk.de.
What is 3D puff embroidery?
A sheet of foam, usually 3 mm thick, is placed on the fabric and covered with dense satin stitches. The needle perforates the foam at the edges, the excess is pulled away and the design stands up from the cap.
Which designs are suitable for 3D puff?
Bold, simple shapes and large lettering with satin stitches between 3 and 10 mm wide. Fine lines under 3 mm, small lettering, fill stitches and stretchy fabrics are better kept flat.
Which needle and thread do I need for puff embroidery?
Polyester embroidery thread in weight 40 and a DBxK5 needle in size 75 to 90 with a sharp point, so the foam is cut cleanly. Choose foam in the colour of the thread.
Which machine settings work for 3D foam?
As a starting point reduce the speed to about 700 stitches per minute, raise the presser foot by the foam thickness and check that the upper thread lies cleanly on the foam. Stitch the flat parts first, then the 3D parts, and always run a test piece.
Why is foam showing through my stitches?
Usually the density is too low or the ends of the satin columns are open. Use about double density and close every end with stitches at 90 or 45 degrees.
What is 3D puff embroidery?
A sheet of foam, usually 3 mm thick, is placed on the fabric and covered with dense satin stitches. The needle perforates the foam at the edges, the excess is pulled away and the design stands up from the cap.
Which designs are suitable for 3D puff?
Bold, simple shapes and large lettering with satin stitches between 3 and 10 mm wide. Fine lines under 3 mm, small lettering, fill stitches and stretchy fabrics are better kept flat.
Which needle and thread do I need for puff embroidery?
Polyester embroidery thread in weight 40 and a DBxK5 needle in size 75 to 90 with a sharp point, so the foam is cut cleanly. Choose foam in the colour of the thread.
Which machine settings work for 3D foam?
As a starting point reduce the speed to about 700 stitches per minute, raise the presser foot by the foam thickness and check that the upper thread lies cleanly on the foam. Stitch the flat parts first, then the 3D parts, and always run a test piece.
Why is foam showing through my stitches?
Usually the density is too low or the ends of the satin columns are open. Use about double density and close every end with stitches at 90 or 45 degrees.
What you will use in this course
Material and next steps for your 3D caps:
Lesson 1 · The idea
Würker 3D Puffy foam, 3 mm, hard, in six colours (article no. O-000-0623 to O-000-0628)
Lesson 2 · Material
Würker cap backing, 100 gsm (article no. O-000-0665-m)
Lesson 3 · Digitizing
Digitizing with BasePac , the course for clean 3D embroidery files
Lesson 4 · On the cap
DBxK5 embroidery needles , size 75 to 90
Lesson 5 · Troubleshooting
A fresh needle, firm foam and one test piece.
New to embroidery?
Start with The Embroidery Starter Kit, also free
Prefer to learn in person?
Ask for a personal 3D puff training at your machine: software@zsk.de
Lesson 1 · The idea
Würker 3D Puffy foam, 3 mm, hard, in six colours (article no. O-000-0623 to O-000-0628)
Lesson 2 · Material
Würker cap backing, 100 gsm (article no. O-000-0665-m)
Lesson 3 · Digitizing
Digitizing with BasePac , the course for clean 3D embroidery files
Lesson 4 · On the cap
DBxK5 embroidery needles , size 75 to 90
Lesson 5 · Troubleshooting
A fresh needle, firm foam and one test piece.
New to embroidery?
Start with The Embroidery Starter Kit, also free
Prefer to learn in person?
Ask for a personal 3D puff training at your machine: software@zsk.de
