Backing decides whether a design lies flat or distorts. With seven qualities, the Würker range covers almost every application in garment decoration. Here is which backing belongs where. All backings are available pre-cut in 20 × 20, 25 × 25 and 40 × 40 cm in the ZSK Parts Shop.
Four steps to the right backing
1. Does the fabric stretch? Yes (jersey, polo, sweat, knits): cut-away, it stays in the garment. No (shirt, canvas, denim, felt): tear-away, it is torn off.
2. How heavy is the fabric, how dense the design? The higher both are, the heavier the backing: 60 g/m² for small chest logos, 80 g/m² for large, dense designs.
3. Does the surface have texture? On piqué, fleece, terry and corduroy add a water-soluble topping.
4. When in doubt, stitch a sample. There is no formula linking weight and stitch count.
Tear-away soft 60 g/m²
For stable, light wovens: shirts, blouses, poplin. The soft finish belongs wherever the back touches the skin. It does not scratch and leaves only fine fibres that wash out. For very thin poplin with a dense design, a cut-away 60 g/m² is the safe alternative. To the product
Tear-away soft 80 g/m²
For heavier wovens and dense designs: work shirts, jackets, canvas, woven terry. The right choice where 60 g/m² gives way under the stitch density. Still soft and comfortable on garments worn close to the body. To the product
Tear-away hard 60 g/m²
For firm wovens where the back does not touch the skin: bags, felt, light canvas, emblems. The hard finish tears cleanly and straight and leaves almost no fibres, which pays off with detailed designs and lettering. On shirts and blouses, prefer the soft version. To the product
Tear-away hard 80 g/m²
For heavy, firm materials: denim, workwear, canvas, bags, emblems and caps. The most stable tear-away, for large and densely stitched logos. On caps use two layers or go straight to the cap backing with 100 g/m². On thin fabrics the firm tear can pull the stitches, so use the soft version there. To the product
Cut-away 60 g/m²
For stretchy knits with small designs: T-shirts, jersey, performance shirts, light polos. It stays in the garment permanently and is only trimmed back. 60 g/m² is enough for a chest logo on thin fabric. On thin, light-coloured performance wear the backing edge can show through. To the product
Cut-away 65 g/m²
The all-round weight for knits of all kinds: T-shirts, polos, piqué, sweatshirts, light fleece. If you want to stock just one cut-away, take this one. On piqué and fleece add a water-soluble topping. To the product
Cut-away 80 g/m²
For heavy and very stretchy knits: sweatshirts, fleece, knitwear, large back designs. If one layer is not enough, add a light tear-away at the very bottom of the hoop, not a second cut-away on top. More than three layers is a sign that the design is stitched too densely. To the product
The most common mistake
Tear-away on knits. The needle perforates it, it loses its support while stitching, and the design distorts at the latest after the first wash.
How it sits in the hoop
From top to bottom: water-soluble topping (if needed), fabric, backing. Always hoop the backing all the way round.
The full range: Würker backings in the ZSK Parts Shop. The free course The Embroidery Starter Kit shows the basics of hooping.
Four steps to the right backing
1. Does the fabric stretch? Yes (jersey, polo, sweat, knits): cut-away, it stays in the garment. No (shirt, canvas, denim, felt): tear-away, it is torn off.
2. How heavy is the fabric, how dense the design? The higher both are, the heavier the backing: 60 g/m² for small chest logos, 80 g/m² for large, dense designs.
3. Does the surface have texture? On piqué, fleece, terry and corduroy add a water-soluble topping.
4. When in doubt, stitch a sample. There is no formula linking weight and stitch count.
Tear-away soft 60 g/m²
For stable, light wovens: shirts, blouses, poplin. The soft finish belongs wherever the back touches the skin. It does not scratch and leaves only fine fibres that wash out. For very thin poplin with a dense design, a cut-away 60 g/m² is the safe alternative. To the product
Tear-away soft 80 g/m²
For heavier wovens and dense designs: work shirts, jackets, canvas, woven terry. The right choice where 60 g/m² gives way under the stitch density. Still soft and comfortable on garments worn close to the body. To the product
Tear-away hard 60 g/m²
For firm wovens where the back does not touch the skin: bags, felt, light canvas, emblems. The hard finish tears cleanly and straight and leaves almost no fibres, which pays off with detailed designs and lettering. On shirts and blouses, prefer the soft version. To the product
Tear-away hard 80 g/m²
For heavy, firm materials: denim, workwear, canvas, bags, emblems and caps. The most stable tear-away, for large and densely stitched logos. On caps use two layers or go straight to the cap backing with 100 g/m². On thin fabrics the firm tear can pull the stitches, so use the soft version there. To the product
Cut-away 60 g/m²
For stretchy knits with small designs: T-shirts, jersey, performance shirts, light polos. It stays in the garment permanently and is only trimmed back. 60 g/m² is enough for a chest logo on thin fabric. On thin, light-coloured performance wear the backing edge can show through. To the product
Cut-away 65 g/m²
The all-round weight for knits of all kinds: T-shirts, polos, piqué, sweatshirts, light fleece. If you want to stock just one cut-away, take this one. On piqué and fleece add a water-soluble topping. To the product
Cut-away 80 g/m²
For heavy and very stretchy knits: sweatshirts, fleece, knitwear, large back designs. If one layer is not enough, add a light tear-away at the very bottom of the hoop, not a second cut-away on top. More than three layers is a sign that the design is stitched too densely. To the product
The most common mistake
Tear-away on knits. The needle perforates it, it loses its support while stitching, and the design distorts at the latest after the first wash.
How it sits in the hoop
From top to bottom: water-soluble topping (if needed), fabric, backing. Always hoop the backing all the way round.
The full range: Würker backings in the ZSK Parts Shop. The free course The Embroidery Starter Kit shows the basics of hooping.
